Open-Hearth Furnace - раздел Иностранные языки, АНГЛИЙСКИЙ ЯЗЫК The Phenomenal Success Of The Bessemer Process Attracted Many Other Inventors...
The phenomenal success of the Bessemer process attracted many other inventors to the study of new and improved methods of steelmaking. The only process which was destined to become a rival of the Bessemer process was developed through the invention of the regenerative principle by Siemens.
Briefly the method of Siemens was as follows: a covered hearth was used to contain the charge of pig iron or pig iron and scrap. Most of the heat required to promote the chemical reactions necessary for purification of the charge was provided by passing burning fuel gas over the top of materials. The fuel gas, with a quantity of air more than sufficient to burn it, was introduced through ports at each end of the furnace, alternately at one end and then the other. The products of combustion passed out of the port which was not used for entrance of gas and air, and entered the chambers partly filled with brick checkerwork. During their passage through the checkers, the gases gave up a large part of their heat to the brickwork. After a short time, the air and gas were shut off at one end and introduced into the furnace through the preheated checkers, absorbing some of the heat stored in these checkers. The gas and air were thus preheated to a somewhat elevated temperature, and consequently developed a higher temperature in combustion than could be obtained without preheating. In about twenty minutes, the flow of the gas and air was again reversed so that they entered the furnace through the checkers and port used first. A series of such reversals, occurring every 15 or 20 minutes, was continued until the heat was finished.
The open-hearth furnace is both reverberatory and regenerative. It is reverberatory in that charge is melted on a refractory hearth, which is shallow, by passing a flame over the charge. The charge and the relatively low roof (above the hearth) built of refractory brick, are heated by the flame with a part of the heating effect on the charge being due to the radiation from the heated roof.
An open-hearth furnace consists of the furnace proper containing the covered hearth on which the charge is placed; ports for admitting the fuel and air for combustion to produce a flame which flows over the charge from the incoming port to the outgoing ports; regenerative chambers containing brick known as "the checkerwork (checkers)" which store up heat transferred to them from the products of combustion; flues and uptakes connecting the checker chambers with the furnace proper; slag pockets which are located at the base of the uptakes; flues leading from the air supply to the regenerative chambers, with connections to the stack; valves (dampers) for regulating flow of air, fuel gas and waste gases; and the stack itself.
Open-hearth furnaces are usually referred to as "acid" or "basic". If the furnace is made of dolomite or magnesia, it is called "a basic hearth", and so lime, which is chemically a basic material, can be added to the slag without causing damage to the hearth. Sulphur and phosphorus can be removed. If the hearth is made of silica sand, very little lime can be added, because it would attack the silica hearth. Hence, sulphur and phosphorus cannot be removed. Such a hearth is known as "an acid hearth". The steel made on it, which is called "acid steel", is generally of high quality.
Scrap is placed on the hearth by means of a charging machine. Limestone is next placed on top of the scrap and then more scrap is added. When this is partially melted, andsome of the metal has combined with oxygen to give FeO, a quantity of hot metal is added by means of a ladle. The carbon in the iron reacts with the ferrous oxide :
C+FeO=Fe+CO,
giving off large volumes of carbon monoxide.
When the desirable carbon content has been reached and the amounts of other elements are satisfactory, the metal istapped.
The fuel may be blast furnace gas, coke oven gas, tar, oil, natural gas.
Most of the open hearth furnaces that have been built during the last few years, have capacities between 200 and 800 tons per heat.
Дополнительные слова и словосочетания:
1) coke-oven gas – коксовый газ
2) reverberatory furnace – отражательная печь
3) regenerative principle – регенеративный принцип
VII. Определите, соответствуют ли содержанию текста данные утверждения.
1. The open-hearth furnace is both reverberatory and regenerative.
2. Traditionally, steelmaking has played a leading role in the economy.
3. The fuel may be blast furnace gas, coke oven gas, tar, oil, natural gas.
4. Molten steel is poured into large molds and solidified.
5. The carbon in the iron reacts with the ferrous oxide giving off large volumes of carbon monoxide.
VIII. Пользуясь текстом, переведите данные предложения на английский язык.
1. Лом поступает в горн при помощи загрузочной машины.
2. Холодные газ и воздух проходят через нагретые насадки регенераторов и сгорают в печи.
3. Продукты горения выходят через отверстия, которые не используются для впуска газа и воздуха.
4. Перекидка осуществляется каждые 15 – 20 минут.
5. Применение нагретого воздуха и газа дает возможность получить более высокие температуры в печи и значительно сократить расход тепла.
IX. Вставьте нужные по смыслу слова, в соответствии с содержанием текста.
1. Scrap is placed … by means of a charging machine.
a) into large molds;
b) on the hearth;
c) acid open-hearth.
2. After a short time, … were shut off at one end and introduced into the furnace through the preheated checkers.
a) loosely laid brick;
b) natural gas;
c) the air and gas.
3. The only process which was destined to become a rival of the Bessemer process was developed … of the regenerative principle by Siemens.
a) through elimination of impurities;
b) through the invention;
c) through recarburising agents.
4. The products of combustion passed out of the port which was not used for entrance of gas and air, and … partly filled with brick checkerwork.
a) broken slowly;
b) entered the chambers;
c) produced in pasty condition.
5. The gas and air were thus preheated to a somewhat elevated temperature, and consequently developed … a in combustion than could be obtained without preheating.
a) toughness and ductility;
b) higher temperature;
c) crystalline in character.
X. Задайте все возможные типы вопросов к данным предложениям.
1. An open-hearth furnace consists of the covered hearth, ports, regenerative chambers containing brick known as "the checkerwork (checkers)"
2. Open-hearth furnaces are usually referred to as "acid" or "basic.
3. Most of the heat was provided by passing burning fuel gas over the top of materials.
XI. Используя рис.2 (см. приложение), опишите мартеновскую печь.
XII. Переведите дополнительный текст без словаря.
About 1850 several revolutions in steelmaking took place. Until then steel had been made in small quantities in clay pots. A few years later it was being made in small quantities of several tons at a time. This led to the modern furnace the capacity of which may exceed 500 tons. The inventions of Frederick and William Siemens, who patented their first furnace in 1865, have had a great effect on the steel industry. The key idea behind the Siemens process is the preheating of the air and gas used to melt the charge. This preheating takes place before the air and gas enter the furnace by passing them through chambers filled with hot bricks. The bricks are heated by the waste gases when the furnace is working in the opposite direction, the flow of air and gas through the furnace being periodically reversed.
Федеральное агентство по образованию... Южно Уральский государственный университет... Кафедра английского языка...
Если Вам нужно дополнительный материал на эту тему, или Вы не нашли то, что искали, рекомендуем воспользоваться поиском по нашей базе работ:
Open-Hearth Furnace
Что будем делать с полученным материалом:
Если этот материал оказался полезным ля Вас, Вы можете сохранить его на свою страничку в социальных сетях:
My Speciality
I. Повторите и запомните следующие слова:
1) choose (chose,
chosen), v
– выбирать
2) daily, adj
My Speciality
There are many faculties in the South Urals State University. But those students who have chosen the career in metallurgy study at the Metallurgical department. I’m a student of the Metallurgical D
Ferrous and Non-Ferrous Metals. Alloys
I. Повторите, запомните следующие слова:
1) appearance, n – внешний вид
2) compose, v – составлять
3) dense, a – плотный
4) feature, n – особенно
Ferrous and Non-Ferrous Metals. Alloys
It is known that metals are very important in our life. Metals have the greatest importance for industry. About two thirds of all elements found in the earth are metals. It is diffi
Iron and Iron Ores
I. Повторите и запомните следующие слова:
1) associate, v – соединять(ся)
2) as well as – также, а также
3) cheap, a – дешевый
4) cost, n – стоимость
5)
Iron and Iron Ores
Iron is the only metal that can be found in almost every part of the world. It’s the fourth element in abundance on the earth, being exceeded by oxygen, silicon and aluminum. It is the cheapest of
Grey Cast Iron
I. Повторите и запомните следующие слова:
1) distribution, n – распределение, распространение
2) flake, n – чешуйка, хлопья (мн.ч.)
3) include, v – включать
4) s
Grey Cast Iron
Grey cast iron is one of the most valued of cast metals. It may be made by melting pig iron and scrap in the cheapest of melting processes, the cupola, and then cast into sand molds
Casting
I. Повторите и запомните следующие слова:
1) accurate, a – точный
2) allow, v – позволять, разрешать
3) cavity, n – полость, пустота
4) hot, a – горячий
Casting
Casting is the oldest method of forming metals. Basically it consists of melting and pouring liquid metal into a cavity of the desired size and shape and allowing the metal to solidify. There are n
Metals and Non–Metals
I. Повторите и запомните следующие слова и словосочетания:
1) alloying element – легирующий элемент
2) alkali metal – щелочной металл
3) base metal – основной металл
Metals and Non–Metals
Among the more obvious distinctions between different kinds of elements is that which divides metals and nonmetals. Metals are distinguished from nonmetals by their high conductivity for heat and e
Corrosion
I. Повторите и запомните следующие слова:
1) damp air – влажный воздух
2) deposit, n – осадок, осаждать
3) destruction, n – разрушение
4) dilute,
Corrosion
It has long been known that metals can undergo changes in which they lose their characteristic properties; in most cases, the metal ceases to be an element, and becomes a compound. Iron exposed to
The Iron Blast Furnace
I. Повторите и запомните следующие слова:
1) carry up, v – поднимать
2) consume, v – потреблять
3) drop, v – опускать
4) float, v – плавать
5) flow, n –
The Iron Blast Furnace
Pig iron is one of the most important materials produced in the metallurgical industry. It is generally produced from the iron ore by chemical reduction process of iron conducted in
Bessemer Converter
I. Повторите, запомните следующие слова:
1) affinity, n – сродство, родственность
2) capacity, n – емкость, мощность, производительность
3) interior, n – внутренность, вн
Bessemer Converter
Molten pig iron, gaseous oxygen and steel scrap are the main constituents for making steel in the converter. Pig iron contains carbon, manganese, phosphorus, sulphur and silicon in
Open-Hearth Furnace
I. Повторите и запомните следующие слова:
1) damper, n – заглушка
2) capacity, n, v – емкость, производительность
3) checkerwork, n – насадка
4) combustion, n –
Electric Furnace
I. Повторите и запомните следующие слова:
1) accomplish, v – совершать, выполнять
2) advantage, n – преимущество, польза
3) arc, n – дуга
4) conductor, n – прово
Electric Furnace
Numerous types of furnaces utilizing electric current as the source of heat have been developed by a large number of investigators, but relatively few types have survived as practic
Continuous Casting of Steel
I. Повторите и запомните следующие слова:
1) apply, v – применять, прикладывать
2) completely, adv – совершенно, полностью
3) conventional, adj – общепринятый, стандартны
Continuous Casting of Steel
Continuous casting as at present applied to the production of steel may be defined as a process in which liquid metal is poured into an open-ended mould, from the lower end of which a partially sol
Types of Mills
I. Повторите и запомните следующие слова:
1) accessories, n – принадлежности, арматура
2) billet, n – заготовка, сутунка
3) blooms, n – блюм, стальная болванка
4
Types of Mills
The three principal types of rolling mills used for the rolling of steel are referred to as "two-high", "three-high", and "four-high mills". As the names indicate, the
The Physics and Chemistry of Metallurgy
I. Повторите и запомните следующие слова:
1) fundamentals, n – основы
2) matter, n – материя, вещество,
3) correlation, n – соотношение
4. to reveal, v –
The physics and chemistry of metallurgy
Metallurgy is a science dealing with the constitution, structure and properties of metals and alloys, and the processes by which they are obtained from ores and adapted for the use
Relation of Metallurgy to Physics and Chemistry
I. Повторите и запомните следующие слова:
1) involve, v – включать в себя, подразумевать
2) outwardly, adv – внешне, снаружи
3) earthy, a – земляной, зерн
Relation of Metallurgy to Physics and Chemistry
In principle, steelmaking involves only a relatively, outwardly simple steps. Principal iron ores consist of combinations of iron with oxygen (iron oxides), mixed with varying percentages of useles
Protection of Steel from Corrosion
I. Повторите и запомните следующие слова:
1) application, n – применение, приведение в действие 2) environment, n – окружающая среда
3) coat, v – грунтовать, нанос
Protection of Steel from Corrosion
Everybody knows how widely steel and iron products are used. But almost in all applications regardless of the environment, these products are coated by some means in order to preven
Induction Furnaces. Puddling Furnaces.
I. Повторите и запомните следующие слова:
1) core, n – сердечник, стержень
2) excess, n – избыток, излишек
3) insure, v – обеспечивать
4) quite, adv – впо
Induction Furnaces. Puddling Furnaces
Induction Furnaces. Induction furnaces are of two types – the coreless high-frequency type and the cored units which operate at low frequency. Principles of operation of both units are simil
Problems of Automation of Blast Furnace
I. Повторите и запомните следующие слова:
1) considerable, a – значительный, важный, большой
2) associated, а – связанный, объединенный
3) denote, v – означать
Problems of Automation of Blast Furnace
In the course of the past few years, a considerable amount of time and money has been spent studying the blast furnace process, and discussing with the operators some of the problems associated wit
Hot Working and Hot Working Processes
I. Повторите и запомните следующие слова:
1) bar, n пруток, – брусок
2) draw, v – тянуть, волочить (проволоку)
3) hammer, n,v – молот, ковать
4) prevent, n – пре
Hot Working and Hot Working Processes
Hot working entails plastic deformation of metals at temperatures where strain hardening does not occur. Hot working is done for two reasons: to shape metal into useful objects; and
Cold Working and Cold Working Processes
Cold working drastically changes the mechanical properties of metals, the most important being increase in strength and hardness with a simultaneous reduction of ductility. The meta
Oxy-fuel combustion for reheat furnaces
Steel Times International APRIL 2002
The use of oxy-fuel burners in reheat furnaces greatly reduces the volume of flue gas produced which in turn leads to lower h
Heat transfer.
The total heat transfer occurring within a furnace can be broken down into four main areas:
– radiant heat transfer from the flame to the product;
– radiant heat transfer from the
Benefits of oxy-fuel combustion.
The main benefits of oxy-fuel can be summarized as:
Higher furnace productivity. As a result of the improved thermal efficiency of the furnace and the improved heat transfer charact
Energy efficiency.
The steel industry's generation of carbon dioxide (CO2) is mainly associated with the chemical reaction of carbon and iron ore in blast furnaces producing molten iron, which is then conv
Energy taxation.
The European Commission proposed in March 1997 a Directive for restructuring the Community framework for the taxation of energy products – COM(97) 30 – and various alternatives have been discussed
Emission trading.
On 23 October 2001 the European Commission adopted a proposal for a Directive of the European Parliament and of the Council establishing a framework for greenhouse gas emission trading within the E
Mill roll lubrication to cut costs
A 15% reduction in mill power consumption, a 10% increase in work roll life and a 20% reduction of mill load are the result of employing hot mill roll lubricants. The correct sel
Cold rolling.
Different parameters are required for the cold rolling mill, where the selection of a robust product will pay for itself in terms of maximizing speeds and strip quality, increasing roll life and ex
Uzbekistan woos foreign investors
Uzbek iron and steel works Joint Stock Manufacturing Amalgamation (Uzmetcombinat) was established in 1994 through a merger of the Uzbek metallurgy plant, the Shirin machine building
СПИСОК СОКРАЩЕНИЙ
1. General Electric Co. – Company
2. Ltd (Britain) - limited responsibility – корпорация из нескольких
владельцев и вице президентов 3. OD. – outside diameter 4. ID. – ins
Хотите получать на электронную почту самые свежие новости?
Подпишитесь на Нашу рассылку
Наша политика приватности обеспечивает 100% безопасность и анонимность Ваших E-Mail
Новости и инфо для студентов